MME Index

• .EMM 30 - enter restricted Master Mode.
• .EMMS 40 - enter Master Mode full version.
• CONSOL 41 - type console commands from a program.
• GEBORT 8 - abort program.
• GECALL 18 - load/call a system program or overlay.
• GECHEK - checkpoint snapshot.
• GEENDC 14 - end courtesy call.
• GEFADD 3 - Get file/device info from file code.
• GEFCON 10 - get file/device info for FCB(s).
• GEFILS - switch primary and secondary logical units.
• GEFINI - normal termination of current job activity.
• GEFRCE - produce diagnostic and abort (ISP and Label).
• GEFSYE - file system call.
• • 10 - modify catalog.
  • 11 - modify file.
  • 2 - create catalog.
  • 22 - file release (no purge).
  • 23 - get information about file.
  • 28 - turn security lock on or off.
  • 29 - turn abort lock on or off.
  • 3 - create file.
  • 30 - miscellaneous transaction processing operations.
  • • 1 - reserve a page for current job only.
    • 2 - set to read from duplicate.
    • 3 - set to read from original.
    • 4 - establish range of ACCESS/MONITOR/ protection.
    • 5 - reserve a page for shared use.
    • 6 - release non-updated page.
  • 34 - identify defective space.
  • 35 - replace and/or re-mark defective spacce.
  • 38 - turn TDS lock on or off.
  • 39 - truncate file.
  • 40 - cancel file changes.
  • 41 - commit file changes.
  • 43 - obtain information about allocated files.
  • 46 - obtain information about allocated file.
  • 9 - purge file.
• GEGEN - MME interface for GTMS.
• GEIDSE - journalization and subfile page range.
• GEINFO - obtain system information.
• GEINOS - I/O request.
• GELAPS - processor time used so far.
• GELBAR - sub-allocate and babysit child program.
• GELOOP - protect against infinite loops.
• GEMORE - request additional peripherals or memory.
• • 0 - obtain additional memory.
  • 1 - obtain additional 7-track tape.
  • 2 - grow existing file or create temp file.
  • 3 - obtain additional 9-track tape.
  • 4 - access cataloged file.
  • 5 - access random cataloged file.
  • 6 - access sequential cataloged file.
  • 7 - chain to next "" file.
• GEMREL - release memory.
• GENEWS 35 - spawn new job.
• GEPRIO - increase I/O priority of tape file.
• GERELC - wait for any I/O to complete.
• GERELS - deallocate resources or change disposition code.
• GERETS - turn off bits in the program switch word.
• GEROAD - wait until all I/O completes.
• GEROLL - rollback or re-initiate program.
• GEROUT - terminal and remote I/O.
• • 03 - direct access output.
  • 04 - direct access output, then input.
  • 05 - establish terminal communication.
  • 06 - determine terminal type.
  • 17 - disconnect terminal.
  • 20 - direct access current line status.
  • 21 - direct access output, then paper tape input.
  • 22 - accept direct access paper tape input.
  • 25 - switch from TSS mode to direct program access.
  • 26 - switch from direct program access mode to TSS.
  • 27 - switch DAC line to another program.
  • 30 - stop paper tape input.
  • 31 - put line in quick status mode.
  • 32 - extended line status.
  • 44 - extended input line length for DAC programs.
  • 45 - remote status inquiry for break/disconnect report.
• GERSTR - restore data from save file.
• GESAVE - write qstar element.
• GESECR - password encryption.
• GESETS - turn on bits in the program switch word.
• GESNAP - produce snapshot dump.
• GESNUM - generate a SNUMB.
• GESPEC - special interrupt request.
• GESYOT - write on SYSOUT.
• GETIME - obtain date and time.
• GEUSER - user-supplied MME.
• GEWAKE - go to sleep for a time.
• GEXLIT - obtain transliteration table.
• GMODER - turn off process mode options.
• GMODES - turn on process mode options.
• Index for "expl mme"
• M.SDCB - set disk cache handling for a file.